Announcement

Collapse
No announcement yet.

PradoPoint Service Checklist for each Service

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • PradoPoint Service Checklist for each Service

    I have been reading this forum for a while and it's a source of a lot of great information. It'd be good to have a Prado Point guide to everything that's a summary of all the good info. The first one that I thought would be a PradoPoint Service Checklist for each Service. Ie a Booklet that has all the extra things a Prado owner needs to ask for/check or do in addition to each scheduled service for example. Maybe a series of these could be developed and sold to fund the website. Just a thought.

  • #2
    Originally posted by Andyfive View Post
    I have been reading this forum for a while and it's a source of a lot of great information. It'd be good to have a Prado Point guide to everything that's a summary of all the good info. The first one that I thought would be a PradoPoint Service Checklist for each Service. Ie a Booklet that has all the extra things a Prado owner needs to ask for/check or do in addition to each scheduled service for example. Maybe a series of these could be developed and sold to fund the website. Just a thought.
    Not a bad idea...There is a fair bit of work in getting such a document prepared and published (unless it remains electronic of course), but if someone has the time and required resources...
    Interested to hear others thoughts.
    Spilsy
    Today is the tomorrow you were shitting yourself about yesterday - Billy Thorpe

    Comment


    • #3
      If you charge for it then all sorts of legal problems arise I would think.

      I do think that a list like that would generate a lot of traffic for the website which would generate income.

      If there was a thread headed up something like "How to Service a Prado" then each topic was listed either as "What to check at 10K service" What to check at 20K service or "How to change oil" "How to check brakes" etc then the bots would find all that and if someone runs a search through Google etc then it will show PP

      ####### has put up a lot of stuff like that already, click on his name then his posts and have a read when you have a lot of spare time

      Comment


      • #4
        Ill do that thanks.

        Comment


        • #5
          As far as parts & replacing here is what i would recommend on a 1kd-ftv
          The usual checks & inspects apply, unless stated otherwise.

          0k put 7mm plate in.
          Every 5k change engine oil.
          Every 10k oil & filter & full diagnostic to check injectors, check/change air filter if used in dusty conditions.
          Every 20k rear fuel filter, rear diff oil if LSD, lubricate driveline.
          Every 30k air filter, more often if dusty. Clean maf sensor.
          Every 40k brake/clutch fluid, f&r diff, oils change, under bonnet fuel filter change.
          Every 50k auto trans flush first time at 100k, then every 50k.
          Every 100k transfer case oil change, auto fluid flush, first at 100k, then every 50k.
          Every 120k replace injectors, check valve clearances for first time, confirm ok for another 120k.
          Every 150k timing belt change.
          Every 160k coolant flush first at 160 or 6 years, then every 80k or 2 years. Replace map filter.
          Every 200k drive belt change.
          Every 250k front wheel bearings, if they make it.
          Every 300k add tensioner & idler pulley to timing belt job.

          Will update the things I forgot as I remember.

          Cheers,

          ####.

          Comment


          • #6
            Can I add a check of suspension bushes every service, particularly for those of us that use it off-road. Also check tension on bar work mounting bolts (they have a nasty habit of rattling loose) and visually check inner guards every service, best to catch those cracks early if they are going to make an appearance. Also it might seem stupid but don't forget to check the tyre pressure of the spare, especially those of us who don't rotate it through and have it hidden under the cover. Just a few silly things that I see often overlooked on "new" vehicles.
            [LEFT]Silver 150 Facelift
            TJM Bullbar, Lightforce Genisis Spots, Dual Battery System with bits from everyone, Powerful 4x4 slider/steps, Kaymar rear bar, "Genuine" Roof Racks, MSA Seatcovers, Dashmat, Tint, LED Interior Globes, Bridgestone D697s [/LEFT]

            Comment


            • #7
              Originally posted by AussieAndy View Post
              Can I add a check of suspension bushes every service, particularly for those of us that use it off-road. Also check tension on bar work mounting bolts (they have a nasty habit of rattling loose) and visually check inner guards every service, best to catch those cracks early if they are going to make an appearance. Also it might seem stupid but don't forget to check the tyre pressure of the spare, especially those of us who don't rotate it through and have it hidden under the cover. Just a few silly things that I see often overlooked on "new" vehicles.
              Sure thing, checks are part of every service.
              Are you having a lot of issues with bushes? Which ones? Would you mind putting some nice pics up?
              Maybe we need a bush thread?
              Always pay attention to the aftermarket items nuts & bolts like bullbar, it's usually the add ons that come or got left loose.
              Cheers.

              Comment


              • #8
                Dont forget the brake pads and rotors

                Comment


                • #9
                  Originally posted by Anth120playdo View Post
                  Sure thing, checks are part of every service.
                  Are you having a lot of issues with bushes? Which ones? Would you mind putting some nice pics up?
                  Maybe we need a bush thread?
                  Always pay attention to the aftermarket items nuts & bolts like bullbar, it's usually the add ons that come or got left loose.
                  Cheers.
                  Yeah, checks SHOULD be part of every service, I just know some people see "new car" and don't bother too much.
                  Not really having a lot of issues with bushes, just the normal flogged out front strut lower bushes from overloaded work utes. Also see the odd one or two flogged out shockie bushes, usually the uppers. Not Prado specific, just vehicle driving on our shitty roads specific.
                  I see way to much aftermarket added equipment held on with loose bolts. Bullbars are common, as are u-bolts on leaf sprung vehicles that have been lifted.
                  I know these are checks that should be done, but all too often they become part of the "tick and flick" environment of servicing we seem to be experiencing more and more often. Also the use of loctite or similar does not mean it won't come loose, it just makes certain things feel tight even if they are not (stretched u-bolts, trailer hitch mounting bolts, etc.)
                  [LEFT]Silver 150 Facelift
                  TJM Bullbar, Lightforce Genisis Spots, Dual Battery System with bits from everyone, Powerful 4x4 slider/steps, Kaymar rear bar, "Genuine" Roof Racks, MSA Seatcovers, Dashmat, Tint, LED Interior Globes, Bridgestone D697s [/LEFT]

                  Comment


                  • #10
                    Originally posted by Anth120playdo View Post
                    As far as parts & replacing here is what i would recommend on a 1kd-ftv
                    The usual checks & inspects apply, unless stated otherwise.

                    0k put 7mm plate in.
                    Every 5k change engine oil.
                    Every 10k oil & filter & full diagnostic to check injectors, check/change air filter if used in dusty conditions.
                    Every 20k rear fuel filter, rear diff oil if LSD, lubricate driveline.
                    Every 30k air filter, more often if dusty. Clean maf sensor.
                    Every 40k brake/clutch fluid, f&r diff, oils change, under bonnet fuel filter change.
                    Every 50k auto trans flush first time at 100k, then every 50k.
                    Every 100k transfer case oil change, auto fluid flush, first at 100k, then every 50k.
                    Every 120k replace injectors, check valve clearances for first time, confirm ok for another 120k.
                    Every 150k timing belt change.
                    Every 160k coolant flush first at 160 or 6 years, then every 80k or 2 years. Replace map filter.
                    Every 200k drive belt change.
                    Every 250k front wheel bearings, if they make it.
                    Every 300k add tensioner & idler pulley to timing belt job.

                    Will update the things I forgot as I remember.

                    Cheers,

                    ####.
                    That's a great start. Thanks.

                    Comment


                    • #11
                      Originally posted by Anth120playdo View Post
                      As far as parts & replacing here is what i would recommend on a 1kd-ftv
                      The usual checks & inspects apply, unless stated otherwise.

                      0k put 7mm plate in.
                      Every 5k change engine oil.
                      Every 10k oil & filter & full diagnostic to check injectors, check/change air filter if used in dusty conditions.
                      Every 20k rear fuel filter, rear diff oil if LSD, lubricate driveline.
                      Every 30k air filter, more often if dusty. Clean maf sensor.
                      Every 40k brake/clutch fluid, f&r diff, oils change, under bonnet fuel filter change.
                      Every 50k auto trans flush first time at 100k, then every 50k.
                      Every 100k transfer case oil change, auto fluid flush, first at 100k, then every 50k.
                      Every 120k replace injectors, check valve clearances for first time, confirm ok for another 120k.
                      Every 150k timing belt change.
                      Every 160k coolant flush first at 160 or 6 years, then every 80k or 2 years. Replace map filter.
                      Every 200k drive belt change.
                      Every 250k front wheel bearings, if they make it.
                      Every 300k add tensioner & idler pulley to timing belt job.

                      Will update the things I forgot as I remember.

                      Cheers,

                      ####.
                      Saved to my "Prado advice file"

                      Comment


                      • #12
                        This is a summary from the Toyota Warranty and Service Booklet for:

                        150 Prado GD Auto


                        Service Item Typical conditions: Adverse conditions *
                        Engine oil (7.7 litres, 0W30 C2 oil) Replace 10,000km 5,000km
                        Engine Oil filter Replace 10,000km 5,000km
                        Engine Air filter Replace 40,000km 5,000km (&clean often
                        Main fuel filter Replace 40,000km 20,000km (&drain 5,000
                        Fuel transfer filter Replace 20,000km
                        Fuel Transfer Pump Replace 150,000km
                        Brake fluid Replace 40,000km or when > moisture
                        Auto trans fluid* Not Specified* Replace every 80,000km
                        Power Steering Fluid Not specified (I'll replace say 80,000
                        Air con pollen filter Replace 30,000km 15,000km (clean often
                        Air con regas/service Not specified As required
                        Valve clearances Not required on GD engine
                        Drive belt Not specified Inspect as required
                        Timing belt Not required (GD has Timing Chain)
                        Engine coolant (including intercooler coolant) R 160,000km, then @ 80,000km
                        F & R differential oil Replace 40,000km 20,000km
                        Transfer case oil Not specified Replace 40,000km
                        Lube prop shaft (and drive train) Lube every 10,000km Lube every 5,000km
                        Tyre rotation & balance Every 10,000km
                        Wheel alignment Every 20,000km
                        Wiper rubbers as required as required
                        Brake pads as required as required
                        Park Brake Adjustment as required as required
                        Clean MAF sensor Clean every 60,000km Clean every 20,000km
                        *Additional service requirements when driving under adverse conditions, which could include any or all of the following:
                        Driving on rough, muddy or snow melted roads.
                        Driving on dusty roads
                        Towing trailers, caravans or boats, or using a car top carrier
                        Repeated short trips, less than 8km, in freezing conditions
                        Extensive idling and or low speed driving for long distances, such as taxis, couriers etc
                        Continuous high speed driving (at speeds over 140km/hr) for over 2 hrs
                        Using fuel from above ground tanks

                        Note: Section 2 Warranty & Service Booklet:
                        Oil thickening
                        Oil thickening is a phenomenon which occurs when particles of unburnt fuel and combustion by-products cause a build up of carbon (soot) in the engine oil forming a jelly type substance. It can cause serious engine damage through oil starvation. It is essential that the engine oil is changed according to the maintenance schedule at either the time or distance specified.

                        I change the oil filter at 5,000km as I'm changing the engine oil, as I usually drive under adverse conditions, so I do what the schedule indicates, and that's change the oil filter as well....and it might just help prevent or reduce the "oil thickening" issue that some folk experience, hopefully the injector seats are now ok, but even if they leak at some stage, by inspecting the oil pickup at regular intervals I should hopefully avoid the clogged oil pickup issue some have seen with other models.

                        Toyota don't specify the auto transmission fluid interval under normal conditions, but I'd agree with #### also, and change at say 50,000km. I'm not intending on replacing injectors at 120K, but rather monitor injector feedback values and make a decision. I got almost 250,000km with my previous D4D Prado, and had the injector feedback monitored by my diesel fitter, and values remained nicely within spec thankfully.
                        SE Qld: GX 150GD Auto, (Feb'16 build): TJM T15 steel b bar, 9,500lb TORQ winch, TJM s steps, Rhino Pioneer Platform (42102B 1928X1236mm), front recovery points, Wynnum towbar, P3 brake controller, TNN Underbody guards, UHF, TREKtable & LED striplight, Custom Fridge & Drawers, Waeco CFX50, 9inch illuminator 160W LED spots, 40mm lifted Dobinson Suspension (Zordo's), ScanguageII, 30 Sec Wing Awning

                        Comment


                        • #13
                          https://toyotamanuals.com.au/

                          https://toyotamanuals.com.au/docs/la...oct-09-dec-11/

                          Comment


                          • #14

                            Thanks for the links oceanracer.
                            Just for information though, the online manuals aren't available as yet for the new GD Prado, so I've summarised the service booklet. I personally use a spreadsheet where I can track all the service items, because it takes a little bit of effort to refer to all sections of the service booklet, especially the additional service requirements, which are tucked in the back of the booklet, and you have to work out which bits apply to the diesel, which bits apply to the petrol, and which bits apply to the auto or manual...its not hard, just takes a bit of wading through the tables...so I just have made a single spreadsheet/table so its makes it easy and quick for my model to see what needs doing and when..with some additional items like auto fluid and transmission fluid etc
                            SE Qld: GX 150GD Auto, (Feb'16 build): TJM T15 steel b bar, 9,500lb TORQ winch, TJM s steps, Rhino Pioneer Platform (42102B 1928X1236mm), front recovery points, Wynnum towbar, P3 brake controller, TNN Underbody guards, UHF, TREKtable & LED striplight, Custom Fridge & Drawers, Waeco CFX50, 9inch illuminator 160W LED spots, 40mm lifted Dobinson Suspension (Zordo's), ScanguageII, 30 Sec Wing Awning

                            Comment


                            • #15
                              Do all Prado 120s have the rear fuel filter?

                              Comment

                              canli bahis siteleri bahis siteleri ecebet.net
                              mencisport.com
                              antalya escort
                              tsyd.org deneme bonusu veren siteler
                              deneme bonusu veren siteler
                              gaziantep escort
                              gaziantep escort
                              asyabahis maltcasino olabahis olabahis
                              erotik film izle Rus escort gaziantep rus escort
                              atasehir escort tuzla escort
                              sikis sex hatti
                              en iyi casino siteleri
                              deneme bonusu veren siteler
                              casibom
                              deneme bonusu veren siteler
                              deneme bonusu veren siteler
                              betticket istanbulbahis
                              Working...
                              X