What did you do to your 90 today?

[RanJ Avid PP Poster! Find all posts View Profile Close RanJ]

Something like this to replace it with?

[ATTACH=CONFIG]20578[/ATTACH]

You might be on to something there!

[Darran K Member Find all posts View Profile Close Darran K]

Fitted a Rhino Rack Tradie tray today to take more stuff camping.

[LAP004 Junior Member Find all posts View Profile Close LAP004]

Fitted a Rhino Rack Tradie tray today to take more stuff camping.

nice looking rack.

today i done this to mine

[Darran K Member Find all posts View Profile Close Darran K]

Awesome. Wish i was out in the mud.

Tomorrow, refit awning, shovel holder to new rack and fit up a dual battery gauge.

[Ian Reid Advanced Member Find all posts View Profile Close Ian Reid]

What did you do to your 90 today?

Fitted a Rhino Rack Tradie tray today to take more stuff camping.

Looks like the same rack i fitted to mine last week. 45107 from memory.


Sent from my iGizmo using Tapatalk

[LAP004 Junior Member Find all posts View Profile Close LAP004]

nice looking rack.

today i done this to mine
[ATTACH=CONFIG]20612[/ATTACH]

MUD WAS AWESOME FUN YESTERDAY
today i got rid of the evidence of the fun then went for a nice country drive

[LAP004 Junior Member Find all posts View Profile Close LAP004]

Fitted snorkal to the prado today.

[RanJ Avid PP Poster! Find all posts View Profile Close RanJ]

Fitted the dobinsons a few weeks ago, but only three... never did the passenger front as I ran out of time. Well, yesterday I found that time! w00t! I swear my front climbed another inch! haha

[JKAF Junior Member Find all posts View Profile Close JKAF]

Finally finished installed a heat exchanger. Works better than I expected. No more cold showers while camping. Just need to have lots of water

I also made some switch plates with my 3D printer and now have a set of 4 rocket launch type switches in my dash (RH side of steering wheel. Yes .... Geeky thing to do, but I think they look good. Wired one up as a master power for the front and rear diff locks. Now to connect something up to the rest of them

[Walky88 Member Find all posts View Profile Close Walky88]

Finally finished installed a heat exchanger. Works better than I expected. No more cold showers while camping. Just need to have lots of water

I also made some switch plates with my 3D printer and now have a set of 4 rocket launch type switches in my dash (RH side of steering wheel. Yes .... Geeky thing to do, but I think they look good. Wired one up as a master power for the front and rear diff locks. Now to connect something up to the rest of them

Can i please see a picture of these???

[Walky88 Member Find all posts View Profile Close Walky88]

Finally finished installed a heat exchanger. Works better than I expected. No more cold showers while camping. Just need to have lots of water

I also made some switch plates with my 3D printer and now have a set of 4 rocket launch type switches in my dash (RH side of steering wheel. Yes .... Geeky thing to do, but I think they look good. Wired one up as a master power for the front and rear diff locks. Now to connect something up to the rest of them

Can i please see a picture of these???

[JKAF Junior Member Find all posts View Profile Close JKAF]

Walky88, Here is a quick snap of the switches.

[gabe1001 Lurker Find all posts View Profile Close gabe1001]

Not today but in the last few weeks I finally had my winch fitted and put some weather shields on that I bought off Ebay
http://i350.photobucket.com/albums/q...pshjgxmhgg.jpg
http://i350.photobucket.com/albums/q...psa4xrrtkx.jpg
http://i350.photobucket.com/albums/q...psvatjzmmh.jpg

[LAP004 Junior Member Find all posts View Profile Close LAP004]

Today i fitted the diffs gearbox and transfer case breathers to my 95.

ordered a light bar for my roof cage.

[Darran K Member Find all posts View Profile Close Darran K]

Booked in for a timing belt tomorrow. Ouch.