What did you do to your 120 today?

[D4D Addicted PP Member Find all posts View Profile Close D4D]

Got it back from the panel beaters (neighbour owns a panel shop) after getting a new rear bar fitted. Asked him to do a small mod when he painted it. I think it turned out ok.

[Wtrxprs007 Senior Member Find all posts View Profile Close Wtrxprs007]

Got it back from the panel beaters (neighbour owns a panel shop) after getting a new rear bar fitted. Asked him to do a small mod when he painted it. I think it turned out ok.

Took me a little bit to notice what he did Haha. Looks good. Been thinking of doing the same myself.

[Corigator Avid PP Poster! Find all posts View Profile Close Corigator]

Did you do that in gloss or satin?

Just thinking of potential scratches.

[D4D Addicted PP Member Find all posts View Profile Close D4D]

Did you do that in gloss or satin?

Just thinking of potential scratches.

Satin

Day time shot

[r4ndll Avid PP Poster! Find all posts View Profile Close r4ndll]

Replaced the second Polyair bag in 2 years. The right side went at 6 yrs old and the left at 8 years old.

[cybr Lurker Find all posts View Profile Close cybr]

Fitted 2 usb charge thingys 1 full live 1 ign live.
fitted a set of cheap ebay hid 100w 7 inch lights
Repaired the horn after 5 years not working.
Turned out to be faulty power feed from front fuse box.
Ended up installing new relay with fuse by the inside fuse box. Located the trigger wire from steering wheel.
Located the horn feed wire. Took power from main feed at bottom of inside fuse box, linked feed and power for relay together, used the trigger from horn onto relay earth,
And fed out going power to horn feed. Horn now working as should.....apart from that strangled chook sound, Stebble air horn in the mail. Will be fitted as soon as it arrives

[ejukated Senior Member Find all posts View Profile Close ejukated]

Crawled under to change the clutch slave, found the LH CV oil seal leaking diff oil... Added to the repair list.

[mikenzaa Junior Member Find all posts View Profile Close mikenzaa]

Spent $2100 at the Melbourne 4x4 show.
Safari snorkel
Redarc Smart start Isolator and 52mm EGT/Boost/ Oil Temp gauge ( 3 in 1)
ARB Under body plates
Diesel care 2nd fuel filter
Flashlube Catch can Pro
All fitted

[Wtrxprs007 Senior Member Find all posts View Profile Close Wtrxprs007]

Added a front hub to my parts-to-order list. Attempted to seperate the bearing from the hub. Did. Not. Work. Well. now she just sits at work in pieces waiting for parts. Hopefully can get it finished tomorrow. Then I'm getting a new driveshaft

[Wtrxprs007 Senior Member Find all posts View Profile Close Wtrxprs007]

Finished my wheel bearing and replaced a driveshaft. She drives like new again

[craigm Addicted PP Member Find all posts View Profile Close craigm]

What was the symptoms for the front bearing Wtrxprs007? I have a squealing noise and occasional clicking when under load. If it was just clicking I would of thought CV for sure. But this is in a straight line only and as said, only when under load. If I idle it goes away. Put it in neutral and rev, nothing. It sounds very much like a bearing.


Sent from my iPhone thingy

[Razorback81 Advanced Member Find all posts View Profile Close Razorback81]

craigm, just jack up the front wheels & feel the top to bottom movement (push/pull the top & bottom of the tyre)

mine had only 90k on them and they were stuffed ( previous owner had done a few water crossings)
mine had no noise , no issues just notice the play in the wheel while on the hoist

[Wtrxprs007 Senior Member Find all posts View Profile Close Wtrxprs007]

What was the symptoms for the front bearing Wtrxprs007? I have a squealing noise and occasional clicking when under load. If it was just clicking I would of thought CV for sure. But this is in a straight line only and as said, only when under load. If I idle it goes away. Put it in neutral and rev, nothing. It sounds very much like a bearing.


Sent from my iPhone thingy

hmm, you issue sounds weird. I'd check for anything rubbing like the backing plate behind the rotor, not sure.

How I found my wheel bearing was just one day I had the car in the air, and there was a LOT of play in the wheel when you move it at 12 and 6. Weirdly, I had no noise at all before I found it.

wouldn't think a bad bearing would be squealing or clicking when driving though

[photoprado Avid PP Poster! Find all posts View Profile Close photoprado]

Did some hard work today, but had to down tools because there was a delivery!

Drifta drawers turned up at the front door, installed them in notime. Still have to do the side infil pieces yet.



Very nice fit, and easy!

[OldGreyFart Advanced Member Find all posts View Profile Close OldGreyFart]

Installed the HKB voltage booster and immediately saw an increase at idle from 13.7v to 14.4v. Very happy with this.