Tweet
wanted a diff drop down kit-
or information on bolt sizes and packer heights
or information on bolt sizes and packer heights
-
-
I do a kit to suit my bashplates. $40 a set which consists of
2 spacers
2 longer HT bolts
4 flat washers
2 nylocks
If you've got factory or other aftermarket bashplates, then you'll need to space them down as well. -
The kit above is very well made and excellent value.2008 Diesel Prado with extra stuff added. I drive it on the road and other places too.Comment
-
AMTS,
Do you have any of these kits in stock now? I wouldn't mind grabbing a set from you if you have.
I've just been speaking to my mechanic about the loss of grease from my CV's and he mentioned the CV angle is a bit too much. If I could, I wouldn't mind getting it in this weekend so I can then get the CV's rectified.
Cheers.04 GXL - Red Centa dual battery, Alloy B/bar, BFG AT's, Rhino Rack commercial bars x 3, GME TX3540, TJM roof cage, Outback Ideas recovery points, LHS rear drawer, 2" Dobinsons/Bilstein lift, ARB CKMA12 air compressor, CoilRite airbags, ARB 2.5m awning, MCC Dual Wheel Carrier, Eagle Eye headlights with 55w hid lo beam.Comment
-
Yes they are.
I'm home now.Comment
-
Cool, thanks. I'll send you an SMS when the wife gets home with the Prado.
I'm not going anywhere without a car with airconditioning today.04 GXL - Red Centa dual battery, Alloy B/bar, BFG AT's, Rhino Rack commercial bars x 3, GME TX3540, TJM roof cage, Outback Ideas recovery points, LHS rear drawer, 2" Dobinsons/Bilstein lift, ARB CKMA12 air compressor, CoilRite airbags, ARB 2.5m awning, MCC Dual Wheel Carrier, Eagle Eye headlights with 55w hid lo beam.Comment
-
OK. Kit is ready for you.
Comment
-
I really should install mine..... Have had these sitting in my tool trolly for the better part of a year
my cvs are the same, have a little bit if grease weeping past the boot since the lift went in
Sent from my iPad using Tapatalk HD2008 120 Series 3lt D4D TD Prado GX, With to many bits to list :-) and more to come!!
Ghosts Build thread :- [url]http://www.pradopoint.com/showthread.php?22132-Ghosts-2008-D4D-Auto-build[/url]Comment
-
I just put my 2" inch lift in and was told I did not need to drop the diff. From what Gramps and Ghost are saying I tend to think a cheap diff drop is good insurance. Might have to invest in an AMTS kit with bonus 120 bash plate :-).2005 V6 VX Pearl White with more and more extras thanks to PPComment
-
Yea same cookie, I was always told I shouldn't really need them, but it really can't hurt putting them on. It's not a massive weep, but it's evident on both left and right sides. I've just been to lazy to jack her up and remove the bash platesOriginally posted by Cookie120 View Post, oh amts bash plates are well worth it aswel, aaaand if you have an arb or ol bar why not add his new radiator protector plate , I'm going to be the Guinea pig for the Oposite lock bar side, but the measurements are damn near identical to the arb bar.....
Sent from my iPad using Tapatalk HD2008 120 Series 3lt D4D TD Prado GX, With to many bits to list :-) and more to come!!
Ghosts Build thread :- [url]http://www.pradopoint.com/showthread.php?22132-Ghosts-2008-D4D-Auto-build[/url]Comment
-
Ps amts, will send my bill in the mail
Sent from my iPad using Tapatalk HD2008 120 Series 3lt D4D TD Prado GX, With to many bits to list :-) and more to come!!
Ghosts Build thread :- [url]http://www.pradopoint.com/showthread.php?22132-Ghosts-2008-D4D-Auto-build[/url]Comment
-
Originally posted by amts View Post
Hey AMTS, how would you recommend we space the bash plates?
i have the ARB under body protection.
Cheers MattComment
-
I reckon 4 more smaller spacers should do the trick. Need to confirm how ARB's UVP attaches to the chassis near the front diff.Originally posted by Mattpaus View PostComment
Comment