Announcement

Collapse
No announcement yet.

Brains TD 150 GXL

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Brains TD 150 GXL

    Finally starting my build thread even though we have had the Prado for 18 months.

    We replaced a WG Jeep Grand Cherokee Laredo with a Black Toyota D4D Turbo Deisel 150 GXL Landcruiser Prado. Finally my wife had had her Jeep (with all it's issues and expensive servicing) and I got to get our Prado.

    We picked it up February 2010. We initially had a VX ordered but the timing of the departure of the Jeep didn't coincide with the delivery of the VX so we had to take a GXL which was okay by me, it was a Prado.

    This is what it looked like after it was first picked up.



    I had many plans to add some accessories and modifications straight away but the pool we built sucked up some of my Prado funds, well actually all of them.

    First accessory was a Wynnum Towbar - (http://www.pradopoint.com/showthread...l=1#post230912)

    Tinted

    Then some Toyota Rubber mats.

    Installed a DIY Couplertec Heavy Duty Electronic Rust Prevention system (http://www.pradopoint.com/showthread...l=1#post268680)

    Dual Battery Install - http://www.pradopoint.com/showthread...ery-TD-150-GXL

    After the wife had an altercation with the back of a CRV we replaced the plastic at the front with a TJM T13 Steel Winch Bar and an Airtec snorkel at the same time.

    Ironman Performance Suspension Installed - (http://www.pradopoint.com/showthread...ado-150-TD-GXL)

    Lightforce XGT Spotties.

    Replacement Head Unit incorporating 8" screen and GPS/DVD. (http://www.pradopoint.com/showthread...l=1#post311563)

    Finished my dual battery install with the ABR battery monitor and connected rear Anderson and 2nd battery circuit to inside cabin.

    GME TX3440 Install (http://www.pradopoint.com/showthread...l=1#post311322)

    Replaced Grandcraps with Cooper AT3.

    Well had some TJM steel sidesteps installed. Also took the opportunity to get underbody protection and my winch installed. (http://www.pradopoint.com/showthread...l=1#post326468)

    Installed Rear LED light for maximum lighting when camping. (Thanks Richo)
    (http://www.pradopoint.com/showthread...l=1#post391300)

    Installed front camera in Kakadu shroud and connected to 8 inch screen. (http://www.pradopoint.com/showthread...l=1#post329434)

    Got the TJM 'Yalara' Roof top tent and installed on the Rhino Racks along with some custom brackets for the 4 Maxtrax and the TJM side awning.

    Designed, prototyped, tested, manufactured and fitted the TG150 Transfer Case and Actuator Guard.
    ([URL]http://www.pradopoint.com/showthread.php?21682-Brains-TD-150-GXL&p=391293&viewfull=1#post391293[url])

    ([url]http://www.pradopoint.com/showthread.php?24395-Transfer-Case-amp-Actuator-Guard-TG150 [url])

    Available at;
    [URL]http://www.pradopoint.com/showthread.php?23608-Prado-150-Transfer-Case-amp-Actuator-Guard-(TG150)-and-120-Transfer-Case-Guard-(TG120)[URL]

    This was to be a longer project but with some trips planned for the future I do have some deadlines to meet!

    Half way through transformation



    Currently looks like this





    TBC...

    To Do:

    Hannibal or Windcheetah Roof Platform
    Diff Breather extension (half done)
    Drifta Drawers (done)
    Fridge mounted to rear
    Kaymar Bar with Dual Wheel Carriers
    DP Chip
    3" Exhaust
    Air Bags
    Recovery Points (done).
    Last edited by Brains; 01-04-2013, 09:24 AM.
    [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

  • #2
    Nice looking Prado there Paul, good choice in a bar. Now to get that GPS...
    -----------------------
    Daniel
    Toyota Prado 150 Series D4D VX Auto Graphite with a 2009 Jayco Hawk Outback
    My Rig Build Up - [URL="http://www.pradopoint.com/viewtopic.php?f=38&t=9064"]viewtopic.php?f=38&t=9064[/URL]

    Comment


    • #3
      Thanks Daniel. I blame your build up page for inspiring some of the accessories on my rig. It's also helped because I've been able to show the wife what it will look like easily, and that when you get authorisation - if it looks alright.
      [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

      Comment


      • #4
        Alright your turn now to help me, order some 18" OE rims and chuck some BFG all terrains on it, take my wife for a ride and prove to her that it has not made the ride any worse with more noise... Fairs fair mate, I would do it for you.
        -----------------------
        Daniel
        Toyota Prado 150 Series D4D VX Auto Graphite with a 2009 Jayco Hawk Outback
        My Rig Build Up - [URL="http://www.pradopoint.com/viewtopic.php?f=38&t=9064"]viewtopic.php?f=38&t=9064[/URL]

        Comment


        • #5
          Originally posted by Rogerthatv2 View Post
          Alright your turn now to help me, order some 18" OE rims and chuck some BFG all terrains on it, take my wife for a ride and prove to her that it has not made the ride any worse with more noise... Fairs fair mate, I would do it for you.
          I'll even lend you the rims
          Pete - 150 Kakadu, 100 and 80 Series Cruisers

          Comment


          • #6
            But I need 17's for my rig. I have actually been looking at the Bridgestone Duelers as I need to replace our tyres on our car very soon. Pete and Rob both gave them a wrap. And might try and squeeze a lift in by Thursday after Wednesdays run. If I had 18's I'd definately put them on and take your wife for a drive. Are you still going to import your tyres?
            [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

            Comment


            • #7
              Yep, I stopped the order but as I really want BFG All Terrains. The Rugged Terrains look good and I am sure will do the job but for the Cape etc I would rather have the AT's under me... The Duelers would also be a choice but no luck on an 18" tyre. In saying that but the AT22's are not that bad, will keep me going for a while yet.
              -----------------------
              Daniel
              Toyota Prado 150 Series D4D VX Auto Graphite with a 2009 Jayco Hawk Outback
              My Rig Build Up - [URL="http://www.pradopoint.com/viewtopic.php?f=38&t=9064"]viewtopic.php?f=38&t=9064[/URL]

              Comment


              • #8
                Nice one Paul, out little outing on Wednesday cost him a fortune he reckons. But we got the non lifted, grandtrek shod Prado through with the use of the maxtraxs.
                [b]Rob[/b]

                [b]2016 Toyota Hilux SR5 D4D Auto Company Cruiser... [/b].
                [url=http://www.pradopoint.com/showthread.php?23866-Hutch-s-2012-150-GXL-V6-petrol-Auto]Hutch's 2012 Build up[/url]
                [SIGPIC][/SIGPIC]

                Comment


                • #9
                  Maxtrax, another thing to add to the list of items to purchase! I've also got to sort out something with my roof basket and the vehicle fitting in the garage. First thing first, I will be sorting tyres and a lift.
                  Daniel when are you looking at heading to the Cape? We are looking at June/July next year. Therefore I have a countdown to complete the required mods and accessories to the Prado.
                  [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

                  Comment


                  • #10
                    Looking good....makes me think I should get my finger out and start saving for some further mods as well as doing a build up thread. I do like the black, but wife liked the silver, so silver is what we got.
                    2011 D4D Silver pearl GXL manual, Toyota bar, GME3340, Rallye 4000 spot lights (HID upgrade), Dual Batteries, ABR rear power outlets, Rhino roof rails, Safari snorkel

                    Comment


                    • #11
                      Davtan,
                      Originally had a charcoal VX on order for delivery end of Feb but we wanted to get rid of the Jeep before anymore money had to be spent on it, that was Feb 2010. Our VX got pushed back to an April delivery and when I asked what the dealer had I got the option of a diesel GXL in black or nearly black (that dark blue colour) or a petrol Kakadu. As I wanted a diesel and my wife had really wanted a black car black it was. Now I wish I had white or silver. Just hard to keep clean and shows bush pinstriping really well. Let's get as many 150's as we can on here, it's great to see what products people are putting on their Prado's and great resource when you are looking at accessorising or modifying.
                      [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

                      Comment


                      • #12
                        Hey there Brains

                        Looks great, question with your Rhino set up- is that tray set up on a set of sports racks, and what size is that tray-


                        It does look sweet


                        Good stuff

                        Brett
                        Manual GXL150 D4D, Silver,Toyota tow bar, Cooper STs, ARB deluxe winch bar, safari snorkel, ultra quattro 2200 HID, BlackWidow Travelmate drawers, Rhino sportz racks, GME 3540, piranha fridge slide, front recovery points, RedArc Smart Start dual battery system.

                        Comment


                        • #13
                          Brett,

                          The Rhino Rack alloy tray is an AT1510 which is a 1500 x 1010mm (http://www.rhinorack.com.au/AccSubCa...TRAY_35_1.aspx). It sits on top of heavy duty bars which are attached to the factory rails using CXB feet or clamps (http://www.rhinorack.com.au/BarType_..._900012_1.aspx). These are not recommended for the 150 but I managed to fit them as did ABR Sidewinder. I'm looking at my options in regards to lowering the height of my tray but probably need a platform.

                          Rig is booked in for a 2" lift this wednesday. I'm putting an Ironman Foam cell combination in. Will let you know what it's like but from what I have read on other forums they seem to impress users.
                          [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

                          Comment


                          • #14
                            Cool thanks for the info- interesting that you got the heavy duty bars onto you rails- I was told that is impossible!

                            Shame too, as I have just got sports bars fitted, but am keen on a pioneer tray, with the rail options (have an Oztent, too big for a tray) and they currently don't fit the sportz bars- but do fit the heavy duty.

                            May look into them, sure I can flog the sportz bars on ebay or something

                            Your tray looked quite long, wasnt sure if it was a AT1800, must have been the camera angle.
                            Manual GXL150 D4D, Silver,Toyota tow bar, Cooper STs, ARB deluxe winch bar, safari snorkel, ultra quattro 2200 HID, BlackWidow Travelmate drawers, Rhino sportz racks, GME 3540, piranha fridge slide, front recovery points, RedArc Smart Start dual battery system.

                            Comment


                            • #15
                              The CXB are a very tight fit I fitted mine without the rubber inserts, I spoke with ABR Sidewinder and he advised he just used detergent and water to assist with getting the legs attached to the rails.

                              I think I want to change my heavy duty racks for sports bars and I am looking at cutting down the alloy tray to reduce the height. Hopefully this would allow me access to the garage.

                              Anyway just dropped the Prado off at Ironman at Brendale for the lift kit. I have chosen the performance kit with foam cell shocks will post up details if the install in the suspension section and build up.
                              [SIZE=2]Black 2009 150 Series D4D GXL Prado, [B]TG150[/B] Transfer Case & Actuator Guard, TJM T13 bar, TJM 9.5lb Winch, Airtec Snorkel, TJM steel sidesteps and sidebars, TJM Underbody Protection, TJM XGS Gold Suspension, Tinted, ARB Fridge Freezer, Couplertec System, Foxwing Awning, 80AH Dual battery, 8" indash GPS, Wet Seat seatcovers, GME TX3540, TX3110 & TX680, [B][COLOR=#ff6633]Maxtrax[/COLOR][/B], Kaymar Dual Wheel Carrier, Breathers, Federal MT's.[/SIZE]

                              Comment

                              canli bahis siteleri bahis siteleri ecebet.net
                              mencisport.com
                              antalya escort
                              tsyd.org deneme bonusu veren siteler
                              deneme bonusu veren siteler
                              gaziantep escort
                              gaziantep escort
                              asyabahis maltcasino olabahis olabahis
                              erotik film izle Rus escort gaziantep rus escort
                              atasehir escort tuzla escort
                              sikis sex hatti
                              en iyi casino siteleri
                              deneme bonusu veren siteler
                              casibom
                              deneme bonusu veren siteler
                              deneme bonusu veren siteler
                              betticket istanbulbahis
                              Working...
                              X