Announcement

Collapse
No announcement yet.

My IPF 800DSCS HID Conversion

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • My IPF 800DSCS HID Conversion

    Modified my 130W IPF,s buy installing 38W 6000K H3 HID lamps and Igniters.


    Rear View of lamp housing with Rubber Grommets I Blank 1 new 25mm, hole was cut using a chassis punch, painted then h3 lamp and grommet installed.
    I bench tested the first lamp housing with reflector out of housing for 4hours, then a futher test with the grommets installed for 2 hours no problems with excessive heat.
    Sealed grommets with RTV silicon and WP connections with silicon grease.

    Rear view of lamps and Wiring runs.

    [Underside view of igniter mount.

    My $12 NARVA Switch from REPCO "Thanks Chippy"
    07 Upgrade GXL D4D, Manual, Dune,Sov Bar, BFG's, SG11, Redark dual Batts, Extensive Aux wiring, Stebel, LED stop tails, IPF HID's (my mod), 240V Inv, ARB Comp, GME UHF,TPMS, Safari snorkel, GPS,Hilux washers, 40l Engel in 30% pas pos,homemade A/C cond protection plate, polyairs.

  • #2
    Any "action shots?"

    Comment


    • #3
      Action Shot:
      07 Upgrade GXL D4D, Manual, Dune,Sov Bar, BFG's, SG11, Redark dual Batts, Extensive Aux wiring, Stebel, LED stop tails, IPF HID's (my mod), 240V Inv, ARB Comp, GME UHF,TPMS, Safari snorkel, GPS,Hilux washers, 40l Engel in 30% pas pos,homemade A/C cond protection plate, polyairs.

      Comment


      • #4
        Where did you get the HID kits Clifton ?

        Comment


        • #5
          Hi Speedcom,
          Got the kit from Ebay http://stores.ebay.com.au/ORNAGE-AUTO-ACCESSORIES
          H3 6000K if you do this mod you will also need grommets to seal the existing lamp housing holes and a 25mm Steel Chassis punch to make the 25mm diam holes for the HID lamps which come with 25mm rubber grommets fitted.

          Take care when inserting the HID lamps into the reflectors that the spring clips lock in correctly to secure each lamp.

          The ballasts/igniter units are mounted to pretty heavy AL plates as per the pics I also stuck Heavy rubber detuners on each plate , but they are not needed was a bit of overkill.

          The connections are water resistant but I used silicon rubber grease on all connections. I used a 30AMP Relay and 15Amp fuse which I might change as these lamps are only 64Watts but they have a hefty inrush current on ignition of the arcs. But nothing like the original QH 130Watt lamps.

          I have not subjected the car to heavy off-road use yet but so far so good on normall FNQ dirt roads which are normally rough by southern standards.

          Hope this helps
          07 Upgrade GXL D4D, Manual, Dune,Sov Bar, BFG's, SG11, Redark dual Batts, Extensive Aux wiring, Stebel, LED stop tails, IPF HID's (my mod), 240V Inv, ARB Comp, GME UHF,TPMS, Safari snorkel, GPS,Hilux washers, 40l Engel in 30% pas pos,homemade A/C cond protection plate, polyairs.

          Comment

          canli bahis siteleri bahis siteleri ecebet.net
          mencisport.com
          antalya escort
          tsyd.org deneme bonusu veren siteler
          deneme bonusu veren siteler
          gaziantep escort
          gaziantep escort
          asyabahis maltcasino olabahis olabahis
          erotik film izle Rus escort gaziantep rus escort
          atasehir escort tuzla escort
          sikis sex hatti
          en iyi casino siteleri
          deneme bonusu veren siteler
          casibom
          deneme bonusu veren siteler
          deneme bonusu veren siteler
          betticket istanbulbahis
          Working...
          X